1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Inter-Ject International Pty Ltd
3/132 Ross Court. Cleveland. Qld 4163. Australia
2. HAZARDS IDENTIFICATION
Classified as hazardous Dangerous Goods under the NOHSC criteria.
Risk Phrase(s)
R11 Flammable
R36/38 Irritating to eyes and skin
R20/22 Harmful by inhalation and if swallowed
S23 Do not breathe vapour. Avoid contact with skin and eyes. Use in ventilated areas with suitable gloves and eye protection. If swallowed, seek medical advice immediately.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Name CAS Proportion
Methyl Alcohol 67-56-1 60 - 100%
Organic Solvents 10 - 40%
4. FIRST AID MEASURES
Wash off with soap and water. Remove contaminated clothing and launder before reuse.
5. FIRE FIGHTING MEASURES
Product is flammable, vapour/air mixtures may ignite explosively. Product should be stored and used in well ventilated area away from naked flames sparks and other sources of ignition.
2 W E
Fire fighters should wear fully self-contained breathing apparatus, overalls and safety boots.
6. ACCIDENTAL RELEASE MEASURES
Wear protective clothing to avoid exposure. Extinguish all ignition sources. For major spills, dam and recover.Prevent entry in drainage systems and waterways. Collect with absorbent material such as sand or earth.Wash area with large quantities of water. Dispose of waste according to applicable local regulations.
7. HANDLING AND STORAGE
Precautions for Safe Handling Storage
To prevent contact and inhalation, wear appropriate protection. Use only in ventilated area. Do not empty into drains. Store in a cool dry, well ventilated area away from sources of ignition and oxidising agents, out of direct sunlight. Keep container sealed when not in use.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
National Exposure Standards
The time weighted average concentration for this product is: 262 mg/m3 (200 ppm), which means the highest allowable exposure concentration in an 8 hour day for a 5 day working week. The short term exposure limit is: 328 mg/m3 (250 ppm), which is the maximum allowable exposure concentration at any time.
It is recommended to use a half-face filter mask to protect from over exposure by inhalation.
Always wear safety glasses or a face shield.
9. PHYSICAL AND CHEMICAL PROPERTIES
| Property | Unit of Measurement | Typical Value |
| Appearance | Clear, colourless liquid | |
| Boiling Point | °C | 64..5 |
| Flash Point | °C | 11.00 |
| Density @ 15°C | g/ml | 0.79 @ 20°C |
| Vapour Pressure @ 20°C | kpa | 92 mmHg |
| Explosive Limits (LEL - UEL) | % | 7.0 – 36.0 |
| Vapour Density @ 20°C | kpa | 1.10 |
| Autoignition Temperature | °C | 385 |
| Viscosity @ 20°C | cSt | Not Applicable |
| Percent Volatiles | % | 87% |
| Solubility with Water | % w/w | Completely Miscible |
10. STABILITY AND REACTIVITY
No decomposition products except on burning. See Fire fighting Measures.
11. TOXICOLOGICAL INFORMATION
Significant absorption gives rise to severe systemic effects. Symptoms , which vary with dosage, include headache, nausea, temporary or permanent blindness, coma and eventual death. In most cases, fatal doses for humans lie within the range of 150 – 300 ml
Irritating to eyes. Leading to inflammation, tearing, stinging, burred vision and redness
Irritating to skin, causing defatting, redness and itchiness
12. ECOLOGICAL INFORMATION
13. DISPOSAL CONSIDERATIONS
Disposal of the product must be in accordance with applicable local and national regulations.
14. TRANSPORT INFORMATION
This product is classed as Dangerous Goods Class 3, packing group II. Please consult the Australian Dangerous Goods Code for Transport by Road and rail for information.
15. REGULATORY INFORMATION
16. OTHER INFORMATION
End of MSDS